Physical Address

304 North Cardinal St.
Dorchester Center, MA 02124

How To Opticover Wifi Extender Setup? Updated 2023

WiFi routers of the most recent generation are capable of providing a high-quality wireless network connection. Each of them, on the other hand, is confined by the coverage area of their respective networks. There is also the issue of interference, which is dependent on the way your home is configured, on top of everything.

The Opticover Wireless Extender is available in a number of different configurations to meet your needs. For its part, the Opticover N300 is the most well-known of the three models. It will be used as an extension device in this guide for the purposes of the tutorial. If you have another Opticover WiFi extender, you can configure it by following the same steps as detailed here.

How To Opticover Wifi Extender Setup

How To Opticover Wifi Extender Setup
How To Opticover Wifi Extender Setup

Before you begin, it is critical to verify that the Opticover WiFI extender is compatible with your wireless router. The Opticover WiFi extender is available in single-band and dual-band configurations. If your router supports them, you should be fine. Additionally, the setup process is dependent on the band you intend to utilise.

Opticover connects the user in three ways:

  • AP mode, alternatively referred to as access point mode
  • Repeater mode
  • Router mode

With Opticover, you can quickly connect to any router brand available. There are two ways to approach the setup:

  • Optional WPS button
  • Option to log in via the web interface.

Let’s look at both of them in greater detail below.

By the end of this post, you should have extended your WiFi network with the Opticover wireless range extender. Additionally, the extender is compatible with nearly all WiFi routers.

You may also like: How To Connect JBL To Macbook?

Opticover WiFi Repeater Extender Setup WPS Method

If you want to avoid complicated setup and get started quickly with the Opticover WiFi repeater equipment, you must use the WPS method.

It is a straightforward Do-It-Yourself (DIY) technique.

To begin, remove your Opticover WiFi repeater from its packaging. After unboxing, proceed with the steps below.

  • Connect the OptiCover WiFi repeater to a power source. You may use any power wall socket that is supported. To begin, plug in near your WiFi router. It is preferable if you also turned on the power from the right-hand side.
  • On the side of the WiFi extension, you’ll now discover a switch mode.
  • Switch to the Repeater mode from there.
  • Now, for at least SIX SECONDS or until the light flashes, you must push the WPS button. This initiates the WPS.
  • Wait a moment. The Opticover Wi-Fi extension will reboot and then display solid lights to indicate that the connection was established successfully. The signal is solid green in hue.
  • Once the configuration is complete, it’s time to relocate the Opticover extender to a more central location for a more robust wireless network.

The connection can fail in various circumstances. In that scenario, you must make sure that the WiFi network can accept WPS signals before proceeding. It is necessary to log into the WiFi router settings and then enable WPS if it is not enabled by default to perform this check.

Opticover WiFi Repeater Extender Web Interface Setup

Following that, configure the OptiCover WiFi extender’s web interface. This configuration is a little more complicated than the last one, requiring some technical knowledge. This may be challenging if you’ve never worked with WiFi routers before. However, if you follow the procedures precisely, you should be fine. Let us begin.

The Opticover may be connected to your computer using an ethernet cable. This enables you to access the WiFi extender’s configuration from your computer. If you do not have an ethernet cable, you can also use the default WiFi SSID name to connect. The backside contains information on the Opticover WiFI extender’s default IP address.

However, you do not need to hunt for it as we have taken care of it for you. The Opticover’s default IP address is 192.168.188.1.

Additionally, you can access it using the URL -ap. setup.

The login name is not required for the first time login. This indicates that you may leave it empty. Now, the password might be anything from meaningless to admin, 1234, or password.

Now, let’s begin by navigating to the login web interface. The steps to follow are as follows:

  • Ensure that the Opticover extender is plugged into a power outlet. Ascertain that it is in close proximity to your primary Wi-Fi router.
  • Now switch to the repeater mode by pressing the mode button.
  • Then, on your laptop/mobile device/desktop, navigate to the Wi-Fi option.
  • There, you’ll notice the default Wi-Fi SSID for the Opticover Extender.
  • Once connected, you may now navigate to the web browser on your device.
  • From there, type http://ap.setup or http://192.168.188.1 to access the Opticover login page.
  • After a brief delay, the login page will load. Now you must log in using the username and password found on the reverse of the Opticover.

This will bring up the Opticover’s status page. The status page will include the following information:

  • The version of the firmware
  • Uptime
  • Status of the connection
  • Wireless mode

Additionally, you’ll see a wizard menu at the bottom. Once you click that, you’ll need to wait for the list of nearby WIFI networks to repopulate. You must locate your primary WiFi router from the list.

Once that is complete, click on it and input your WiFi password to connect. It would help to input the password to allow the router’s connection to the extender.

From there, you’ll want to configure the repeater’s SSID. The SSID repeater you choose is totally up to you. You can either use the existing WiFi network’s SSID or create a new one. Now, click “Connect” and then “Save Settings.

This will force the WiFi router to reboot. If not, perform a manual reboot and proceed to the next step.

After that, you may check the status of the repeater from the status page. If it is solid green, the connection has been established successfully.

Also read: How to Factory Reset MacBook Pro Without Apple ID Password

Opticover Troubleshooting With Wireless Router

Occasionally, something will go wrong, and you will be unable to connect the extension to your router. That is why you must perform some troubleshooting to make it work.

  • If you are unable to log into the Opticover extender, verify that you are connecting to the right IP address.
  • Additionally, ensure that the WiFi router does not have a static IP address configured.
  • Ascertain that you are logging in with the right username and password.

If nothing else works, you could try doing a factory reset on the wireless range extender. To reset, follow these steps:

  • Connect the repeater to a power outlet to turn it on.
  • Once booted, the repeater will have a little reset button. Additionally, depending on the model, it could be a little hole.
  • Now, press and hold the reset button for an additional 8-10 seconds. It will bring the lighting back to normal. Once complete, shut down the computer and wait for it to reboot. It may take up to 2-3 minutes for the device to reset to factory settings.

You may also like: Best Headphones For Smule

Some Frequently Asked Question

What is the procedure for resetting my opti-cover extender?

The paperclip can be used to press and hold the reset button for ten seconds.

The LED indicator will illuminate to indicate that the unit is rebooting. Allow at least 30 seconds before attempting to access the extension. There is the default IP address.

Why isn’t the LED on opticover lighting up after I’ve completed the process?

While setup, it is conceivable that you input the wrong wifi password for your host wifi network.

How can I reset the factory settings on my Opticover Wireless range extender?

Resetting the extender to factory defaults will clear all configuration and unplug it from any wireless router.
If the range extender is connected but there is no internet, or if you are experiencing connection and disconnect issues with the wifi repeater device, we recommend that you reset the device using the reset button and reconfigure it.

How can I reinstall Opticover Repeater?

Connect the repeater to the socket’s power supply and wait for it to fully boot.

Determine the location of a little reset button.

Hold the button down for 8-10 seconds and then release it when all LED lights go out and come back on quickly.

The extender device will reboot and take around 2-3 minutes to restore factory settings.

After resetting the extender configuration, choose between the WPS or login method.

You might be interested: How to Fix Xbox Error 0x87e5002b?

Final Words

This brings us to the conclusion of our Opticover WiFi extender configuration. You should appropriately configure your repeater if you follow the instructions provided here. Additionally, you can use the manual that is included as a guide.

 

Leave a Reply

Your email address will not be published. Required fields are marked *